Be based on parameter of lathe tool of figuration of SolidWorks feature formative to change a design
- Time:
- Click:156
- source:SHNMIN CNC Machining
1 generate spare parts substance to build a part in SolidWorks, choice level datum plane is mixed for axes of draft plane scale half outline, what the part gets after rotating is hypostatic. It is draft plane with plane of the P in end panel, the relative position of face of the knife before pressing and workpiece (R1=10mm place, with ° of F=10 of γ of horizontal included angle) the picture is linear, excise on half 4b that get a picture point-blank with this. 3.
Design of substance of 2 cutting tool is built in SolidWorks assemble system, insert the part that has completed assemble system, will insert new part to name in assembling system for " cutting tool " : Section of choice work check is draft plane, cite with entity the cut look that the command gets this plane go up: The line that take out part has nothing to do, the line that retains cutting blade share lengthens additional cutting blade, next line of outer side picture forms the graph that close, this graph is the cut form of face of the knife before cutting tool namely. Form of cut of face of the knife before the cutting tool after finishing (swallow end tenon was not drawn, with excision the law realizes) after. It is draft plane with end panel P again, the picture in draft is here linear in order to decide the position of face of the knife after cutting tool, its length (dimension 40) can ask to decide according to the design. Next form of knife face cut is before sectional, hind of knife side position linear (linear) for method, with scanning the command creates cutting tool entity. The underside cutting tool and hind knife face is perpendicular cut neat, reoccupy excises a command to generate swallow end tenon, the design of cutting tool substance is accused namely finish. The axial side of cutting tool, apply colours to a drawing. Express 23 paragraphs, the coordinate of reference point of coordinate value line segment of reference point of curve of 567 paragraphs of batten 23 paragraphs of X=139.
57Y=119.
47Z=0.
00X=137.
74Y=120.
25Z=0.
00X=137.
11Y=121.
03Z=0.
00X=136.
75Y=122.
47Z=0.
00567 paragraphs of X=142.
37Y=111.
97Z=0.
00X=141.
93Y=112.
73Z=0.
00X=141.
63Y=113.
55Z=0.
00X=141.
47Y=114.
41Z=0.
00X=141.
45Y=115.
29Z=0.
00X=141.
57Y=116.
17Z=0.
00X=141.
75Y=117.
03Z=0.
00X=142.
37Y=117.
97Z=0.
003.
3 after generating attempt of cutting tool project to be finished in design of cutting tool substance, does OK and unusual convenient favourable geographical position generate: of attempt of cutting tool project with SolidWorks? Suddenly windows the profile that land ü こ draws out poisonous Bi of slash to weary こ of administer draws out poison of of Ping of sell of H of ability pure umbrella to knock at admire box end to ask ash Zuo to decide proper section plane place can get needing directly in OlidWorks. Example of generated attempt of cutting tool project (did not note dimension) , a-A is form of cut of its method extent. 3.
4 get parameter of form of cut of extent of cutting tool method to be below CAM environment, can get parameter of form of cut of extent of cutting tool method directly, use these parameter process designing next, the cut on online cut machine tool gives cutting tool hind knife face. Is the means that gets parameter in SolidWorks: ? is foolish grave こ draws out command of the Ave As that add Man to be put into Dxf(or Dwg) format, open place to keep Dxf(or Dwg) file in AutoCAD again next, through defining proper coordinate department, with List inquiry command can obtain the parameter of the each line segment in form of method extent cut. 23 paragraphs are mixed 567 paragraphs of line segment, on the part drawing in correspondence 23 paragraphs of element lines that are cone, 567 paragraphs are circular arc, when designing figuration lathe tool with traditional method, also part this two line segment simplify to be mixed point-blank circular arc, but will bring hyperbola error from this. And when applied SolidWorks designs figuration lathe tool, passing List to inquire the command is informed 23 paragraphs is not linear, 567 paragraphs also are not circular arc, however batten curve (it is namely be in one kind a certain number of the curvilinear) that undertakes planning to close between reference point coordinate. The watch listed on mix to 23 paragraphs the inquiry result of coordinate of reference point of curve of 567 paragraphs of batten. If the reader is operated by same method, although coordinate fastens the coordinate that gets differring with the different meeting of graphical position to be worth, but want workpiece and cutting tool parameter to agree only, its are worth relative to coordinate should be identical. 3.
Because SolidWorks is to be based on diagnostic parameter to convert hypostatic modelling software,the parameter of 5 figuration lathe tool changes a design, the change that can adopt measure will have an edition to entity, accordingly, want the work that makes above and cutting tool only assemble body file to regard an example as the file, use the function that undertakes the spare parts is designed in assembly drawing, in the draft plane of the spare parts the profile of redefine spare parts creates new spare parts entity, wait for cutting tool parameter according to F of new requirement redefine γ and α F again, can get new cutting tool entity directly. The project blueprint as a result of Solid-Works is as associated as hypostatic photograph, after getting new cutting tool entity, the profile on project blueprint and dimension can make corresponding change namely, get new cutting tool project pursues. If want to obtain the coordinate parameter of cut form line segment, need plan of will new cutting tool project to be put into Dxf or Dwg file to be in with Save As command only AutoCAD is useful List command undertakes inquiring can. 4 epilogue are based on SolidWorks to be able to be in three-dimensional and hypostatic environment with simulative method implementation turns over look doctrine to machine, the three-dimensional and hypostatic model of easily implementation figuration lathe tool is designed, get attempt of cutting tool project and profile parameter then: SolidWorks is to be based on diagnostic parameter to convert hypostatic modelling software, want those who build a workpiece and cutting tool to assemble body document only, example can is with its in new design, need to have an edition in assembling system only, change the parameter of the profile of the spare parts and cutting tool, can get attempt of project of new cutting tool entity, cutting tool and parameter of cutting tool profile. Accordingly, solidWorks is the three-dimensional design software that Windows system the next goes to the lavatory to learn easily, use the specific method of article introduction, design what raise figuration lathe tool significantly efficiency. CNC Milling CNC Machining